Battery Application Kits

Product Details:

This is first time in India when we offer Battery Hydrometer to Indian industry. Till date all battery people use are glass type bulb hydrometers which has main drawback is that it's glass material use. We are using acid proof acrylic material to manufacture our cell safe hydrometer. This Battery Hydrometer is useful in any battery industry. Moreover, we assure the timely delivery of this product.

Features

• Unbreakable as made from acid proof acrylic material.

• First time in India.

• Dial type indication for very easy reading.

• Affordable cost to everyone.

• Long life and lifetime.

Product Details:

Product Description:

• Our attery Desulfator is a advanced state of the art fully automatic electronic device which produces a unique pulse by using power from battery itself. The pulse waveform has a strictly controlled signal amplitude, rise time, frequency and on off time. The cell safe works on all types of lead acid batteries. It is a fit and forget device. It’s operation is fully automatic and no attention is required. As mentioned above, the irreversible sulfation formation is very slow process and does not form in few days. It is a cyclic process; initial small irreversible sulfation leads to prevent charging. Now less charging leads to more IRR. Sulfation and vice versa. If you see the graph of any lead battery life, then you will come to know that the battery which works 100% for first 2 years dies only in next 6 months time.

• Cell safe works 24 hours and 365 days. It provides a unique pulse waveform which gives vibratory shocks to both plates. This time is very short in microseconds so the IRR sulfate crystals formed on plates gets debonded and returned to electrolyte solution as active material.This process and action is repeated unless until battery voltage is decreases to 10.5 V DC in Inverter model and 12.5 V DC in automobile model.

Advantages:

• No irreversible sulfation formation throughout the battery life (if installed on new battery or within 4- 6 months)
• Battery will remain in peak condition
• Battery’s internal impedance will be reduced
• The electrolyte temp. will be minimum
• Less or almost nil DM water topping is required
• No boiling of electrolyte hence no acid fumes or acid smelling
• A sulfated battery requires more electricity for charging process. This is because of high battery impedance
• Guaranteed double battery life in normal working conditions

Product Details:

• Plastic. Chamber with 2 Glass Trays.
• Imported UV tube
• Emits UV light.
• Effective tool for avoiding contamination of instruments, once sterilized or autoclaved.
• Can maintain & preserve instruments for days without any fear of contamination.
• Door switch interlock prevents emission of UV light as soon as the chamber is opened to avoid any harmful effect on operator.
• Electronic circuit for instant start of tube.

Additional Information:

• Item Code: UV-18
• Production Capacity: 50
• Delivery Time: 4 days

Product Details:

This system contains below parts and its description is as below:

• Battery watering plug (BWP): This plug is made from polyprolene material. It will allow water inside only when the electrolyte level is below plastic float inside. Please note that this BWP will not work on gravity water pressure. It requires Minimum 10 psi water pressure for normal operation. Each BWP has one adaptor for easy fitting in 30 MM TYPE THREAD CELL VENT PLUG. ( there is one more adaptor for lift battery cell 35 mm push in type )
•  Water feeding pump: It is a 12 v dc windshield washer Pump required to pump and supply water to BWP with pressure. There are two wires coming from battery (on which this system is installed) through Push to on switch. When the switch is pressed then Pump will get on and supply water to BWP (at a time to six nos. plugs.) Please refer images.
• DM water tank: It is a 5 liters tank used to store dm water. The water feed Pump is mounted on this tank only.
  
• Blue Color PU Tubing. : We are providing tubing in continuous shape. And user needs to cut the tube as req. and installed in between two plugs. There is blue color PVC dead cap to use in extreme last plug. Please see photo for ref.
• Small Plastic Connector: This connector connects 4 mm PU pipe from Pump with 6 m PU pipe to BWP. Please refer images.
•  Push to ON switch and wires: The push to ON switch and wires provides 12 v dc supplies to water feed pump. Please refer image.

Other Instructions:

•  The BWP is a low weight delicate, accurate, sensitive plastic moulded and assembled product. So handle it gently, do not apply very high manual pressure to fix in battery cell. Otherwise the top cover will get damage.
•  Keep minimum distance in between DM water tank and Lead acid Battery.
•  When you want to TOP up DM water then simply press and hold Push to ON switch. Now Pump will feed water to each BWP and the flow will become Zero when all Battery cells electrolyte level reaches to BWP float point.
• When you press switch again then as the electrolyte level is there so every BWP will not allow water into battery cell.

Package Contents:

•  Water Storage Tank
•  Pipeline /Water tubes
•  Feed water Pump
• End Plugs
•  Battery watering Plug

Product Details:

This system contains below parts and its description is as below:

•  Battery watering plug (BWP): This plug is made from polyprolene material. It will allow water inside only when the electrolyte level is below plastic float inside. Please note that this BWP will not work on gravity water pressure. It requires Minimum 10 psi water pressure for normal operation. Each BWP has one adaptor for easy fitting in 30 MM TYPE THREAD CELL VENT PLUG. ( there is one more adaptor for lift battery cell 35 mm push in type )

•  Water feeding pump: It is a 12 v dc windshield washer Pump required to pump and supply water to BWP with pressure. There are two wires coming from battery (on which this system is installed) through Push to on switch. When the switch is pressed then Pump will get on and supply water to BWP (at a time to six nos. plugs.) Please refer images.

•  DM water Tank: It is a 5 liters tank used to store dm water. The water feed Pump is mounted on this tank only.
•  Blue color PU Tubing. : We are providing tubing in continuous shape. And user needs to cut the tube as req. and installed in between two plugs. There is blue color PVC dead cap to use in extreme last plug. Please see photo for ref.
• Small Plastic Connector: This connector connects 4 mm PU pipe from Pump with 6 m PU pipe to BWP. Please refer images.
• Push to ON switch and wires: The push to ON switch and wires provides 12 v dc supplies to water feed pump. Please refer image.

Other Instructions:

• The BWP is a low weight delicate, accurate, sensitive plastic moulded and assembled product. So handle it gently, do not apply very high manual pressure to fix in battery cell. Otherwise the top cover will get damage.
• Keep minimum distance in between DM water tank and Lead acid Battery.
•  When you want to TOP up DM water then simply press and hold Push to ON switch. Now Pump will feed water to each BWP and the flow will become Zero when all Battery cells electrolyte level reaches to BWP float point.
• When you press switch again then as the electrolyte level is there so every BWP will not allow water into battery cell.

Package Contents:

• Water Storage Tank
•  Pipeline /Water tubes
• Feed water Pump
•  End Plugs
• Battery watering Plug
• Auto Feed Water Control Unit

Product Details:

Quality Product : Lowest Price : Benefit to the end user :

• Battery watering plug (BWP): This plug is made from polyprolene material. It will allow water inside only when the electrolyte level is below plastic float inside. Please note that this BWP will not work on gravity water pressure. It requires Minimum 10 psi water pressure for normal operation. Each BWP has one adaptor for easy fitting in 30 MM TYPE THREAD CELL VENT PLUG. ( there is one more adaptor for lift battery cell 35 mm push in type ).

•  Water feeding pump: It is a 12 v dc windshield washer Pump required to pump and supply water to BWP with pressure. There are two wires coming from battery (on which this system is installed) through Push to on switch. When the switch is pressed then Pump will get on and supply water to BWP (at a time to six nos. plugs.) Please refer images.

• DM water tank: It is a 5 liters tank used to store dm water. The water feed Pump is mounted on this tank only.

• Blue color PU tubing : We are providing tubing in continuous shape. And user needs to cut the tube as req. and installed in between two plugs. There is blue color PVC dead cap to use in extreme last plug. Please see photo for ref.

• Small Plastic connector: This connector connects 4 mm PU pipe from Pump with 6 m PU pipe to BWP. Please refer images.

• Push to ON switch and wires: The push to ON switch and wires provides 12 v dc supplies to water feed pump. Please refer image.

Other Instructions:

•  The BWP is a low weight delicate, accurate, sensitive plastic moulded and assembled product. So handle it gently, do not apply very high manual pressure to fix in battery cell. Otherwise the top cover will get damage.
•  Keep minimum distance in between DM water tank and Lead acid Battery.
•  When you want to TOP up DM water then simply press and hold Push to ON switch. Now Pump will feed water to each BWP and the flow will become Zero when all Battery cells electrolyte level reaches to BWP float point.
• When you press switch again then as the electrolyte level is there so every BWP will not allow water into battery cell.

Package Contents:

• Water Storage Tank
•  Pipeline /Water tubes
•  Feed water Pump
•  End Plugs
•  Battery watering Plug
•  Auto Feed Water Control Unit